News

Hot dip galvanizing equipment is very advanced and practical. Nowadays, many large enterprises, especially those that use many steel materials, will introduce hot-dip galvanizing equipment, which can produce long-life, stronger and corrosion-resistant products, and can also greatly save resources that are wasted by corrosion.

First, loading The outer surface of the steel pipe shall not be contaminated with impurities and dirt, and no artificial bending damage shall occur. Second, the material is pickled and washed Before hot dip galvanizing equipment, workers must take protective measures and wear overalls. Generally, pickling will use hydrochloric acid. When the tube is down, first place the head that stands on it to prevent splashing of hydrochloric acid. The time is about 5-15 minutes, so you should shake it often. After that, it should be washed with water, and it should be carried out in a flowing clear water tank, and all the steel pipes should be immersed in the clear water pool. After the cleaning is completed, the water should be cleaned and treated as soon as possible to prevent the steel pipe from being oxidized. Third, solvent treatment The steel pipe should be completely immersed in the solvent, wait until the ends do not bubble, then lift the steel pipe from one side, shake up and down, then lift the whole steel pipe to control the net solvent, put it into the control dry frame. Fourth, the steel pipe is dried Drying is mainly to remove water, and then it can also raise the temperature of the steel pipe itself, which can then accelerate the galvanizing. 5. Hot dip galvanizing Finally, the most critical step is to use a fully immersed semi-automatic method for galvanizing steel pipes: pull in, press, rotate, pull out, and then lift. When melting zinc, it should be heated slowly, avoiding rapid fire. Sixth, lead out, blow out After the zinc-plated tube is raised, it is taken out by a magnetic pipe and then blown outside. Compressed air is used for external blowing, preferably at temperatures above 70 degrees.

Hot dip galvanizing is a very effective process to prevent metal corrosion and is widely used in various industrial fields where metals are used. Its simple process is that the iron base forms an alloy with the outer zinc, which has strong adhesion and uniformity and a long service life. So, what are the processes for using Hot dip galvanizing equipment?

The function of the FRP pretreatment Tanks for softening the tank is to play the role of [softening" the water source, mainly for hard water with high calcium and magnesium content, softening hard water. The softening tank is an important part of the softener system. The inside of the softening tank is placed with an ion exchange resin. The working principle of the ion exchange resin can effectively reduce the concentration of calcium and magnesium ions in the water. In general, different types of Pretreatment Tanks are useful. In practical applications, different types of filter tanks and softening tanks are often used together to achieve better water purification.

The filter cans can be specifically divided into three types: mechanical filter cans, multi-media filter cans, and activated carbon filter cans, each of which has advantages, and the actual conditions applied are also different. 1. Mechanical filter tank is the principle of using pressure filter, which is mainly used in the filtration pretreatment system flow of daily water and drinking water. 2. Multi-media Pretreatment tank can effectively remove suspended particles and very fine sand-grain particles in sewage, etc., to achieve better "turbidity" effect, and is more suitable for water treatment with relatively large turbidity. 3. The activated carbon filter tank is further improved. The pigments, tiny suspended particles and the like in the water which cannot be clearly seen in the multi-media filter tank can be effectively adsorbed and removed.

To know how to choose a Pretreatment Tanks, first of all, you must first know its classification, identify which type you need, and then pick the manufacturer, see the price, and see the quality. According to the purpose of classification, can be divided into two types of filter cans and softened cans, let's talk about their specific types.

The product processing of the Fluxing Tank Reprocessing & Regenerating system needs to be strictly controlled. If the flux can be evenly distributed, the influence of the excess flux can be appropriately reduced. Therefore, the flux can be uniformly applied by adjusting the inclination of the solder. In the welding process, if the flux can be strictly controlled, it is natural to improve the welding quality. It is important to control the Fluxing Tank Reprocessing & Regenerating system, but even if the flux is added too much, just take appropriate measures. no problem

The increase in temperature can increase the consumption rate of the flux, so the flux can be accelerated by increasing the temperature, or the time in the constant temperature zone can be extended, the Fluxing Tank Reprocessing & Regenerating system consumption time can be prolonged, and the flux consumption can be increased as much as possible.

In fact, in the welding process, it is difficult to increase the amount of flux added, just a lot, not too much. If the amount of flux added is too small, it is easy to apply unevenly, and eventually the welding is unqualified, and the probability of occurrence of leakage welding, continuous welding, and virtual welding increases. Therefore, in order to ensure the quality of the solder, the Fluxing Tank Reprocessing & Regenerating system is often more or less, as much as possible, but if the flux is too much, it is easy to cause adverse effects, but special methods can be used to allow the excess flux to evaporate. portion.

Most of them have some understanding of the welding work, but it is known that there is less need to add flux during the welding process. The Fluxing Tank Reprocessing & Regenerating system is more important in the welding process. The most common flux is Lead-free solder wire, what should I do if the flux is too much during the soldering process?

As long as it is possible to select the Acid Vapors Lips Collecting & Scrubbing Tower System for the above two points, it can be used well in actual production. Of course, after following these two points, the price chosen must be reasonable and critical. After all, this involves the cost of an industrial production.

In recent years, environmental pollution control has always been a top priority. Therefore, when purchasing Acid Vapors Lips Collecting & Scrubbing Tower System , it is absolutely impossible to be cheap and free to choose. 1, to see the difference in materials between different equipment, as long as the materials are not the same, then their quality will be different. 2, the structure of the equipment is to follow certain rules, only the reasonable structure of the equipment can make recycling more efficient.

For factories that produce a lot of harmful gases during production and processing, Acid Vapors Lips Collecting & Scrubbing Tower System is very important, not only can improve the environment in the workshop, but also further improve the air quality, in addition to the workshop. In addition to the physical health of the staff, the environment can also be protected for a long time. So such a device is absolutely not less.

Most factories have more or less smoke and dust generated during the processing and production. If they are discharged into the air, they will not only pollute the environment, but also endanger the acid rain for a long time. Or acid mist, because the factory does not process the harmful gases emitted, so each factory should have Acid Vapors Lips Collecting & Scrubbing Tower System , then, what are the functions and purchases of such equipment? For factories that produce a lot of harmful gases during production and processing, Acid Vapors Lips Collecting & Scrubbing Tower System is very important, not only can improve the environment in the workshop, but also further improve the air quality, in addition to the workshop.

Hebei Annuo Automation Technology Co,.Ltd. was established in 1998. With many years of experience in the industry, many manufacturers who have just started to contact the hot dip galvanizing line will give priority to the manufacturers. It is also a comprehensive service company integrating environmental protection, hot-dip galvanizing, whole production line consultation, design, manufacture and installation.

What are the regular purchase channels for hot dip galvanizing line ? There are many online hot dip galvanizing line , but there have been changes in the galvanizing equipment and galvanizing lines used in the galvanizing industry. Fully automatic hot dip galvanizing line is a mechanical automation operation, but it is also necessary for someone to supervise from the side, and any problems can be dealt with in the first time. Today's social intelligence is becoming more and more popular. At the same time, the system is intelligent, and the waste of manpower is also minimized. Nowadays, intelligent production has computer monitoring and the program system is more perfect.

Considering the choice of hot dip galvanizing equipment, we should also think about it from the manufacturer side. There are too many brands to choose from now, and you need to choose a comprehensive brand manufacturer. Understand the production methods and operations of different manufacturers and whether the equipment can be used with good stability and safety considerations in order to support the long-term operation of hot dip galvanizing equipment. Nowadays, there are many introductions of hot dip galvanizing equipment on the Internet. It is easy to select and view the introduction, which reduces many important problems and makes the product users have a good experience, so that they get good reviews.

There are many types of hot dip galvanizing equipment, especially in the current industry. The choice of hot dip galvanizing equipment must first understand the equipment, combined with the requirements of self-processing production. It can be classified and modeled by the application of the device, there is no good operation method, and there is no good product guarantee. Can be selected through professional introduction, optimistic about the functional model of hot dip galvanizing equipment, is conducive to support for a long time to use, in order to have a very good product experience.

How abouthot dip galvanizing equipment? The hot dip galvanizing process should be the best process representative in today's social processing. We consider that the processing and production requirements are also classified in the processing equipment. How to choose hot dip galvanizing equipment? This is also a problem for many production and processing companies using hot dip galvanizing equipment. So how about hot dip galvanizing equipment?

It is also necessary to know the production line equipment for small parts galvanizing lines, according to the manufacturer's brand and quotation. Generally, we must first be optimistic about the operation and development of different manufacturers' brands, whether they have good technical strength, and whether they can provide a variety of production line equipment. In addition, it is also necessary to consider the basic quotation of the equipment, etc., so that the appropriate equipment can be selected to support longer-term use, and the operation safety and stability are good. There are many things to know about the selection of small parts galvanizing lines. In the actual selection, you should have a good understanding of the whole, to ensure the stable use of equipment, and more in line with self-processing needs. For the production and processing environment in need, it should also be considered in detail, and the application is better.